Solar Panel and Accessories

LIKET Solar PV Fuse Holder 1P with LED 10x38mm DC1000V with 30A Fuse 

Model: ZTPV-25X
Fuse Size: 10x38mm (30A Fuse Included)
Rated Voltage: DC1000V
Current Rating: 32A Max
Wire Range: 1-10mm²

LIKET Solar PV Fuse Holder 1P with LED 10x38mm DC1000V 

Model: ZTPV-25X
Fuse Size: 10x38mm (No Fuse Included)
Rated Voltage: DC1000V
Current Rating: 32A Max
Wire Range: 1-10mm²

30A 12V/24V Lead-Acid, Gel Battery Solar Charge Controller with DC Jack & Current Reading K-1688

Specification:

Material: ABS + PC
System voltage: 12V/24V automatic adaptation
Rated charging current: 30A
Maximum photovoltaic voltage: 23V for 12V battery; 46V for 24V battery
Boost charging voltage: 14.4V
Floating voltage: 13.7V (default value, adjustable)
Discharge cut-off voltage: 10.7V (default value, adjustable)
Discharge recovery voltage: 12.6V (default value, adjustable)
Charging recovery voltage: 13V
Light-controlled turn-on threshold Photovoltaic panel: 8V (light-controlled turn-on has a delay)
USB output: 2 USB outputs, 5V/2.5A (maximum)
Standby current: <10mA
Working temperature: -35 - +60℃

Recommendations for safe use:

1. This controller automatically recognizes 12V24V. When installing for the first time, please make sure that the battery has enough voltage so that the controller can recognize the correct battery type.
2. Install the controller as close to the battery as possible to avoid voltage drop caused by excessively long wires and affect normal voltage judgment.
3. This controller is only suitable for all kinds of lead-acid batteries (including openings, seals, gels, etc.).
4. This controller can only use photovoltaic panels as the charging source. Do not use DC or other power sources as the charging source.
5. The controller will heat up when it is running, please pay attention to install the controller on a flat, well-ventilated surface.

20A 12V/24V PWM Lead-Acid, Gel Battery Solar Charge Controller W88-B

PWM20
Charging Curren: 20A
Discharging Current: 20A
Max Solar input 50V(for 24V battery) 25V(for 12V battery)
Max PV Input: 260W (12V), 520W (24V)
Equalization 14.4V(Sealed) 14.2V(Gel) 14.6V(Flood)
Float charge 13.7V(defaul,adjustable)
Discharge stop 10.7V(defaul,adjustable)
Discharge reconnect 12.6V(defaul,adjustable)
USB output 5V/3A
Self-consum Operating temperature -35°C~+60°C
Installation Wire Size: 6mm2
Storage temperature -40°C-70°C

Product features:

1. Industrial level main control chip is adopted.
2. Large LCD display, adjustable charging and discharging parameters.
3. Complete 3 phase PWM charging management.
4. Built-in overcurrent/short circuit protection, open circuit protection and reverse connection protection, all of which are self-restoring and will not damage the controller.
5. Double MOS anti-backflow circuit, ultra-low heating value.

30A 12V/24V Lead-Acid, Gel, Lithium Battery Solar Charge Controller W-88C

-This Controller is suitable for 3 types of batterie.Battery type description:
-B1 is a lead-acid batteries(12V/24V auto)
-B2 is a lithium ion batteries(3 strings of 11.1V lithium batteries)Factory setting Default B2
-B3 is a lithium iron phosphate battery(4 strings of 12.8V)
-System Voltage: 12V/24V Auto
-Charge current: 30A
-Max input power and voltage: 390W(12V system); 780W(24V system)
-USB output: Dual USB output, 5V/2.5A
-Equalization: 12.6V(defaul,) / Discharge reconnect voltage: 10.5V(defaul) /Discharge stop voltage: 9(defaul)
-Turn ON/OFF light voltage: Solar pannel 8V.
-Self-consume: <10mA
-Temperature: -35℃~ 60℃

-PWM Charge Controller Protection:
-Dual MOSFET Reverse current
-Over heat protection
-Under-voltage discharge protection
-Short-circuit protection
-Open-circuit protection
-Over-load protection
-Over-charging protection
-Power off memory protection

-Intelligent solar controller:
The product can automatically manage the working of solar panel and battery in solar system. For protecting the lifespan of your battery, once the voltage of the battery drop below 8V, the solar controller will turn off automatically (LCD will be unavailable at the same time).

-Solar Controller System Connection:
-1.Connect the battery to the charge regulator - plus and minus.
-2.Connect the photovoltaic module to the regulator - plus and minus.
-3. Connect the consumer to the charge regulator - plus and minus.
NOTE: The reverse order applies when deinstalling! An improper sequence order can damage the controller!

30A 12V/24V PWM Lead-Acid, Gel Battery Solar Charge Controller W88-B

PWM30
Charging Curren: 30A
Discharging Current: 30A
Max Solar input 50V(for 24V battery) 25V(for 12V battery)
Max PV Input: 390W (12V), 780W (24V)
Equalization 14.4V(Sealed) 14.2V(Gel) 14.6V(Flood)
Float charge 13.7V(defaul,adjustable)
Discharge stop 10.7V(defaul,adjustable)
Discharge reconnect 12.6V(defaul,adjustable)
USB output 5V/3A
Self-consum Operating temperature -35°C~+60°C
Installation Wire Size: 6mm2
Storage temperature -40°C-70°C

Product features:

1. Industrial level main control chip is adopted.
2. Large LCD display, adjustable charging and discharging parameters.
3. Complete 3 phase PWM charging management.
4. Built-in overcurrent/short circuit protection, open circuit protection and reverse connection protection, all of which are self-restoring and will not damage the controller.
5. Double MOS anti-backflow circuit, ultra-low heating value.

EARU 2P 63A AC Manual Change Over Switch for Eskom & Inverter Switch Over AC Protection Combiner Box

- Model: EA219G
- Manual Change Over Switch for Eskom & Inverter AC Protection Combiner Box
- 230/ 400V AC 50/60Hz
- 2P 63A

SINOTIMER Electricity Energy Meter Single Phase Rail Consumption Reset DDS6619-526L-2


- Model: SINOTIMER DDS6619-526L-2
- With backlight function, the value can be clearly seen in the dark environment
- Easy to install
- Large LCD screen
- Display: total power kwh, temporary power kwh, actual voltage, actual current, actual power, long press the button for 6s to reset
- Current: 5 -80A Max
- Voltage: 230V 50Hz
- Pulse: 1000imp/kwh
- Display mode: electronic digital display
- Size: 7.85 x 6.58 x 3.63 cm
- Installation: DIN Rail

GEYA Solar PV DC Surge Protector 2P SPD 1000VDC 40KA GS-P9-C40PV GSP9 DC surge protective device is applied low voltage standard IEC EN 61643-11 to protect against DC power line system and other equipment from over voltage and instantaneous over voltage damage. Widely used in photovoltaic comber box, power inverter, DC distribution cabinet etc. It has advantages of large discharge current, fast respond time, low residual voltage. Max. PV voltage up to UCPV ≤1000V dc. Main features 1. High discharge capacity, quick response, module pluggable; 2. Fast response time, din rail installation; 3. Double thermal disconnection devices, provide more reliable protection; 4. Green window means normal, red means defect, need to change module; 5. Remote alarm terminal optional. 6. T1+T2 surge protection.

GEYA Solar PV MC4 Connectors DC1500V 30A Male Female IP67 - 2 Pairs

- 2 Pairs Solar Panel Cable Connectors (Compatible with MC4) (2pcs MC4 Male and 2pcs MC4 Female).

- WATERPROOF RING on connection is perfect to seal out water and dust to prevent corrosion
- PPO INSULATION MATERIAL with excellent aging resistance and UV endurance, survived rain, high force winds and snow.
- Compatible with PV cables with different insulation diameters (2.5m㎡--6m㎡).
- Quick & simple assembly processing and simple removal of plugs without the aid of any extra instrument.
- Good waterproof performance for outdoors usage.

Specifications

* Rated current: 30A (2.5m㎡--6m㎡)
* Rated voltage: 1500V DC
* Connector contact resistance:≤0.5mΩ
* Degree of waterproof: IP67
* Flammability rating: UL94-V0
* Safety: Class II
* Suitable cable: 2.5m㎡--6m㎡( include AWG13,AWG12, AWG11,AWG10 )
* Adapter Wire: OD 5mm-7mm
* Connector conductor material: copper, Tin
* Connector Insulation material: PPO/PPE
* Insertion force: less or equal to 50N
* Withdrawal force: over or equal to 50N
* Operating temperature range: -40℃～ +85℃
* Connection: Clamp

Package include

* 2x male connectors
* 2x female connectors
* 2 pairs Solar Connector Pins (male & female)