Search results for 'Aux to Bluetooth'

Kobo Touch E-Book Reader Screen Replacement Repairs

- Screen Replacement for Kobo Touch
- Original Screen From Kobo Supplier Chain
- Price Including Installation

30A 12V/24V Lead-Acid, Gel, Lithium Battery Solar Charge Controller CL92

-This Controller is suitable for 3 types of batterie.Battery type description:
-B1 is a lead-acid batteries(12V/24V auto)
-B2 is a lithium ion batteries(3 strings of 11.1V lithium batteries)Factory setting Default B2
-B3 is a lithium iron phosphate battery(4 strings of 12.8V)
-System Voltage: 12V/24V Auto
-Charge current: 30A
-Max input power and voltage: 390W(12V system); 780W(24V system)
-USB output: Dual USB output, 5V/2.5A
-Equalization: 12.6V(defaul,) / Discharge reconnect voltage: 10.5V(defaul) /Discharge stop voltage: 9(defaul)
-Turn ON/OFF light voltage: Solar pannel 8V.
-Self-consume: <10mA
-Temperature: -35℃~ 60℃

-PWM Charge Controller Protection:
-Dual MOSFET Reverse current
-Over heat protection
-Under-voltage discharge protection
-Short-circuit protection
-Open-circuit protection
-Over-load protection
-Over-charging protection
-Power off memory protection

-Intelligent solar controller:
The product can automatically manage the working of solar panel and battery in solar system. For protecting the lifespan of your battery, once the voltage of the battery drop below 8V, the solar controller will turn off automatically (LCD will be unavailable at the same time).

-Solar Controller System Connection:
-1.Connect the battery to the charge regulator - plus and minus.
-2.Connect the photovoltaic module to the regulator - plus and minus.
-3. Connect the consumer to the charge regulator - plus and minus.
NOTE: The reverse order applies when deinstalling! An improper sequence order can damage the controller!

30A 12V/24V PWM Lead-Acid, Gel Battery Solar Charge Controller W88-B

PWM30
Charging Curren: 30A
Discharging Current: 30A
Max Solar input 50V(for 24V battery) 25V(for 12V battery)
Max PV Input: 390W (12V), 780W (24V)
Equalization 14.4V(Sealed) 14.2V(Gel) 14.6V(Flood)
Float charge 13.7V(defaul,adjustable)
Discharge stop 10.7V(defaul,adjustable)
Discharge reconnect 12.6V(defaul,adjustable)
USB output 5V/3A
Self-consum Operating temperature -35°C~+60°C
Installation Wire Size: 6mm2
Storage temperature -40°C-70°C

Product features:

1. Industrial level main control chip is adopted.
2. Large LCD display, adjustable charging and discharging parameters.
3. Complete 3 phase PWM charging management.
4. Built-in overcurrent/short circuit protection, open circuit protection and reverse connection protection, all of which are self-restoring and will not damage the controller.
5. Double MOS anti-backflow circuit, ultra-low heating value.

30A 12V/24V Lead-Acid, Gel, Lithium Battery Solar Charge Controller W-88C

-This Controller is suitable for 3 types of batterie.Battery type description:
-B1 is a lead-acid batteries(12V/24V auto)
-B2 is a lithium ion batteries(3 strings of 11.1V lithium batteries)Factory setting Default B2
-B3 is a lithium iron phosphate battery(4 strings of 12.8V)
-System Voltage: 12V/24V Auto
-Charge current: 30A
-Max input power and voltage: 390W(12V system); 780W(24V system)
-USB output: Dual USB output, 5V/2.5A
-Equalization: 12.6V(defaul,) / Discharge reconnect voltage: 10.5V(defaul) /Discharge stop voltage: 9(defaul)
-Turn ON/OFF light voltage: Solar pannel 8V.
-Self-consume: <10mA
-Temperature: -35℃~ 60℃

-PWM Charge Controller Protection:
-Dual MOSFET Reverse current
-Over heat protection
-Under-voltage discharge protection
-Short-circuit protection
-Open-circuit protection
-Over-load protection
-Over-charging protection
-Power off memory protection

-Intelligent solar controller:
The product can automatically manage the working of solar panel and battery in solar system. For protecting the lifespan of your battery, once the voltage of the battery drop below 8V, the solar controller will turn off automatically (LCD will be unavailable at the same time).

-Solar Controller System Connection:
-1.Connect the battery to the charge regulator - plus and minus.
-2.Connect the photovoltaic module to the regulator - plus and minus.
-3. Connect the consumer to the charge regulator - plus and minus.
NOTE: The reverse order applies when deinstalling! An improper sequence order can damage the controller!

20A 12V/24V PWM Lead-Acid, Gel Battery Solar Charge Controller W88-B

PWM20
Charging Curren: 20A
Discharging Current: 20A
Max Solar input 50V(for 24V battery) 25V(for 12V battery)
Max PV Input: 260W (12V), 520W (24V)
Equalization 14.4V(Sealed) 14.2V(Gel) 14.6V(Flood)
Float charge 13.7V(defaul,adjustable)
Discharge stop 10.7V(defaul,adjustable)
Discharge reconnect 12.6V(defaul,adjustable)
USB output 5V/3A
Self-consum Operating temperature -35°C~+60°C
Installation Wire Size: 6mm2
Storage temperature -40°C-70°C

Product features:

1. Industrial level main control chip is adopted.
2. Large LCD display, adjustable charging and discharging parameters.
3. Complete 3 phase PWM charging management.
4. Built-in overcurrent/short circuit protection, open circuit protection and reverse connection protection, all of which are self-restoring and will not damage the controller.
5. Double MOS anti-backflow circuit, ultra-low heating value.

30A 12V/24V Lead-Acid, Gel Battery Solar Charge Controller with DC Jack & Current Reading K-1688

Specification:

Material: ABS + PC
System voltage: 12V/24V automatic adaptation
Rated charging current: 30A
Maximum photovoltaic voltage: 23V for 12V battery; 46V for 24V battery
Boost charging voltage: 14.4V
Floating voltage: 13.7V (default value, adjustable)
Discharge cut-off voltage: 10.7V (default value, adjustable)
Discharge recovery voltage: 12.6V (default value, adjustable)
Charging recovery voltage: 13V
Light-controlled turn-on threshold Photovoltaic panel: 8V (light-controlled turn-on has a delay)
USB output: 2 USB outputs, 5V/2.5A (maximum)
Standby current: <10mA
Working temperature: -35 - +60℃

Recommendations for safe use:

1. This controller automatically recognizes 12V24V. When installing for the first time, please make sure that the battery has enough voltage so that the controller can recognize the correct battery type.
2. Install the controller as close to the battery as possible to avoid voltage drop caused by excessively long wires and affect normal voltage judgment.
3. This controller is only suitable for all kinds of lead-acid batteries (including openings, seals, gels, etc.).
4. This controller can only use photovoltaic panels as the charging source. Do not use DC or other power sources as the charging source.
5. The controller will heat up when it is running, please pay attention to install the controller on a flat, well-ventilated surface.

Toshiba 15V 5A 75W Notebook Power Adapter 6.3mm x 3.0mm

- Input: 100-240V AC
- Output: 15V 5A DC 75W
- Connector: 6.3mm x 3.0mm

Nokia T20 Tablet Tempered Glass Screen Protector

- Tempered Glass Screen Protector for Nokia T20 Tablet

LIKET Solar PV DC Surge Protector 2P SPD 1000VDC 40KA LKTD2-PV1000

Model: LKTD2-PV1000
Poles: 2P
Un: 1000V DC
Imax: 40kA(8/20)
In: 20kA(8/20)

SINOTIMER Adjustable Over-Voltage Under-Voltage Protector 230V 63A SVP-916

Descriptions:

- SINOTIMER SVP series automatic over-voltage protection device is suitable for single-phase AC voltage 230V, 50/60Hz, rated working current 63A and below users or loads.When the power situation is unstable, it's protection function will be automatically activated.
- It is mainly used for the protection of over-voltage, under-voltage or over-current in the distribution line of residential household box or the protection of single-phase power equipment.
- Its main feature is overvoltage or undervoltage in the line, overcurrent condition, the product can cut off the power supply instantaneously, protect the electrical equipment from being damaged; when the line voltage returns to normal, the protector can automatically turn on the power supply normally.

Features:

1.Stable Performence:The circuit boardss of products adopt good quality electronic components with longer service life and more reliable performance.
2.Easy Installation:35mm standard guide rail installation,easy to mount.
3.Simple Operation:The automatic recovery over voltage and under voltage protective device complies with modular design standards, and its use and maintenance are very simple.
4.Signal Light:The green indicator display, when the power is normal supply. The red indicator display, when the power over voltage or under voltage.
5.Clear Read:Super clear LED display and ultra-wide viewing angle, voltage and current reading can be easily seen at any time.
6.Function:Once the voltage exceeds the limited range of products, it will automatically cut off so as to protect the safely of electrical equipment and persons. The device will re-supply, when the power returns to normal.

Specifications:

- Brand:SINOTIMER
- Name:Undervoltage/Overvoltage Protector
- Model:SVP-916
- Rated AC Voltage:230V AC 50Hz/60Hz
- Passing Max Current: 63A
- Over-voltage Protection Value Range:221V~300~OFF(Default:280V)
- Over-voltage Recovery Voltage Range:220V~299V(Default:250V)
- Over-voltage Protection Action Time:0.1s~10s(Default:0.1s)
- Under-voltage Protection Value Range:150V~219V~OFF(Default:160V)
- Under-voltage Recovery Voltage Range:151V~220V (Default:180V)
- Under-voltage Protection Action Time:0.1s~10s(Default:0.1s)
- Over-current Protection Value Range:1A~63A(Default:63A)
- Over-current Action Range:0.1~512s(Default:5.0s)
- Recovery Time:2s~120s(Default:60s)​​
- Delay Time After Power-on:2s~10s(Default:2s)
- Over-voltage Protection:Yes
- Under-voltage Protection:Yes
- Over-voltage Protection Value Adjustable:Yes
- Over-voltage Recovery Value Adjustable:Yes
- Under-voltage Protection Value Adjustable:Yes
- Under-voltage Recovery Value Adjustable:Yes
- Fault Recovery Delay Time Adjustable:Yes
- Delay Time After Power-on Adjustable:Yes
- Voltage Display(Voltage Measurement):Yes
- Current Display(Current Measurement):Yes
- Over-current Value Adjustable:Yes
- Automatic Recovery:Yes
- Installing:35mm Din Rail
- Size:58x36x65mm/2.28x1.42x2.56in